Autowatch Ghost Immobiliser Installation
The Ghost is the UK's most advanced aftermarket immobiliser that works with CAN buses. It's discreet, doesn't use LED indications or key fobs and is concealed in the vehicle's wiring.
cost of ghost immobiliser allows users to turn off the system temporarily through Transport Mode for when they are renting out their vehicle. This guide will guide you through the process of installing a Ghost immobiliser.
Professional Installation
The Autowatch Ghost immobiliser protects your car against key cloning attacks, hacking attacks and relay attacks. The system is linked directly to the ECU of your vehicle and protected by a PIN code that you choose. It's undetectable to thieves using scanners for diagnostics or other modern methods, and is unable to be disabled through circuit cuts.
The system is easy to use, but professional installation is recommended to ensure a clean connection with the ECU of your vehicle. Installers approved by Thatcham can assist with the installation and programming of your Ghost system. They can also suggest a tracking system or alarm to complement your vehicle's security package.
First, the installer needs to disconnect the battery to prevent accidental airbag deployment or short circuits. Once the battery is disconnected, the installer may be able to work safely. Hand tools are essential for securing connections with precision and a multimeter may be used to verify the electrical properties and safety. Insulation tape and cable tie are vital to secure connections and ensure that wiring is neat. In addition, the user's manual gives specific guidelines that are tailored to the Ghost Immobiliser model you have.
It is crucial to select the right grounding spot that is free of dirt or paint during installation. The installer must ensure that the immobiliser's CAN H as well as CAN L wires are connected to the correct ports on your vehicle's ECU. These wires can be connected or soldered depending on the model. Using a top-quality connector is recommended to ensure a sturdy and reliable connection.
Once the install is complete Once the installation is completed, the customer can enable after the installation is complete, the customer can activate Transport Mode. This allows valet parking or mechanics to use the vehicle without having to know the pin code. The customer must press the service icon on the dashboard five times over two seconds. The system will confirm this by displaying 5 indicators.
The Autowatch Ghost 2 immobiliser is TASSA approved and a highly efficient immobiliser. It's a smart choice for anyone who frequently rents out their cars on platforms like Turo. Immobilisers can lower insurance rates, as it decreases the likelihood of theft.
Getting Started
If you're looking for a solution that will protect your vehicle from thieves it is best to go with an autowatch ghost immobiliser. It prevents your car from starting when someone copies or steals your key. It's possible due to its advanced technology that stops the engine from starting until the right PIN code is entered.
The device connects to the vehicle's bus system CAN and allows direct communication with the ECU. It uses the buttons on your dashboard and steering wheel to create a unique sequence, that only you can understand. This makes it impossible for anyone else to start your car. This is the ultimate system to protect your pride and joy. It will ensure that your car's value remains intact if you ever want to sell it.
Installing Ghost's immobiliser is straightforward, but you must follow the steps to avoid electrical issues and system malfunctions. First, you need to find and locate a permanent 12V power source and an appropriate grounding point on the chassis of your vehicle. Then, you can begin connecting the wires to the immobiliser. Use high-quality connectors, and soldering techniques for a solid connection. Also, make sure to insulate the connections with heat shrink tubing and insulation tape to shield them from short circuits in electrical power and other issues.
Once the wires are connected, you can plug in the battery and start the engine to determine whether the immobiliser works. After you've verified that everything is functioning properly, you can install the immobiliser in a secure position inside the vehicle. Make sure you hide it well to prevent any thief from taking advantage of it.
The Ghost 2 immobiliser is TASSA (Tracker and Aftermarket Security System Association) certified this means it is in compliance with the highest standards of security and is a fantastic protection against car thieves. It is invulnerable to hacking and key cloning and cannot be disabled without the code. The device is also easy to use and can be set into the service valet mode to ensure that your automobile is not activated when you take it in for service or an MOT.
Wiring
The Ghost Immobiliser, a cutting technological security system, has been designed to deter theft of vehicles. It communicates with your vehicle's ECU and connects directly to its CAN bus. Contrary to other aftermarket systems which require the removal of circuit components, the Ghost Immobiliser doesn't interfere with any of the factory settings for your vehicle.
The system is also unnoticeable by thieves using diagnostic scanners. The system doesn't transmit or receive radio frequency signals, but instead uses CAN data for communication with your ECU. In addition, it doesn't need any modification to your car's existing key fobs.
Enter your disarm sequence (either two or one button) and turn on the ignition in your car to activate the Ghost Immobiliser. The indicator will flash two times to verify that you have entered the correct code. After this, you can start your vehicle and drive off safely.
Once installed The Ghost Immobiliser can secure your vehicle from key cloning and hacking while preserving the value of your pride and joy. In Transport Mode you can temporarily disable the Ghost Immobiliser in case you need to give your car over for service or valet parking.
You'll need a constant power source (12V) and an earthing point to complete the installation of the Ghost immobiliser. Ensure that these are both well-insulated and safe to touch. Cable ties are also suggested for bundling and secure the wires. This reduces the possibility of theft by thieves. To avoid making mistakes, double-check these points and mark them using labels or tape. Examine all connections for signs they're wearing out. Loose connections can lead to problems with the system, so be certain that they are securely in place and securely insulated. Finally, don't forget to test the Ghost Immobiliser after the installation is completed. This will make sure that the unit is operating properly and that all connections and insulation are secure. If you encounter any issues, be sure to resolve them immediately.
Testing
The Autowatch Ghost immobiliser is a revolutionary vehicle security system that connects seamlessly with your car's ECU to stop unauthorised motor starting. Its innovative technology safeguards your vehicle against hacking and key cloning and other common methods employed by thieves to steal vehicles. The Ghost also works in tandem with existing alarm and tracking systems to offer the most complete protection for your vehicle. The Ghost's unparalleled features and secluded design make it a preferred choice for car lovers and security-conscious motorists alike.
It is essential to follow the steps of installation to ensure the complete integration of the Ghost Immobiliser. Check the wiring diagram of the vehicle as it will aid you in locating and connecting the wires. After that, you'll need determine the power source and grounding points. Once you've found them, you'll be required to mark the points to make them easily identifiable when installing. It's important to use high-quality materials and tools. Basic hand tools will aid in making precise connections. A multimeter will verify electrical values, and also ensure security. Cable tie and insulation tape will ensure that all connections are tidy. A Ghost-specific user manual is also available.
Before you begin installing it is important to test the system by entering the PIN code, then starting the vehicle. This test will verify that the immobiliser functions as intended and will stop vehicle starts that are not authorized. This procedure should be carried out frequently as part of your regular inspections of your vehicle to ensure the system is working properly.
After the installation is completed, you are now able to start driving your vehicle with confidence. The Ghost will guard your vehicle from would-be car thieves. It will ensure that no one can take your car away without having the correct PIN code. The Ghost can be linked to an approved Thatcham tracker, which detects attempts at theft or tampering. This lets you track your vehicle if it is stolen.
The Ghost is compatible with a wide variety of vehicles, including those made by the majority of major manufacturers. If you're interested in protecting your car with this innovative device, contact Monty's Locksmith today to learn more about our installation and service options. We are a TASSA Registered installer This certification ensures that we adhere to strict guidelines and procedures when installing our products. This assures customers insurance companies, customers, and law enforcement agencies that all installations are performed safely and properly.